RBSS-PS2 Outdoor Motion Detector

PIR and microwave sensing for outdoor approach areas. Battery-powered installation and setup in RB Link help you put detection where your project needs it.

outdoor pir sensor

How does a dual-tech PIR and microwave motion detector work?

A dual-tech detector uses two sensing methods: passive infrared (PIR) senses infrared changes, while microwave sensing detects movement. RBSS-PS2 needs both inputs to trigger an alarm, helping reject disturbances picked up by just one sensor.

If you mount it beside a warehouse entrance, aim it so people walking toward the door cross both detection patterns. Test that route and nearby nuisance sources to check what triggers an alarm.

How does an outdoor dual-tech detector reduce false alarms?

PIR and microwave must both detect activity before RBSS-PS2 triggers an alarm. This helps filter out disturbances picked up by just one sensing method. Activity that affects both can still trigger it.

For example, if you cover an approach beside a hedge or road, keep moving branches and passing traffic outside the detection area where possible. Walk the approach route, then test likely nuisance sources nearby.

Does dual technology provide anti-miss detection?

RBSS-PS2 can miss movement when either sensor receives too weak a signal, because both inputs are needed for an alarm. Walk-test each approach and crossing route at the final mounting position.

For example, if you get no alarm when walking toward a side gate, check for obstructions, then review mounting and sensitivity and repeat the test.

PROJECT SPECIFICATIONS

Project Fit at a Glance

Model
RBSS-PS2
Location
Outdoor
Detection
PIR + microwave
Nominal coverage
Up to 16 m / 90°
Enclosure
IP54
Mounting
1.8–2.2 m · wall mount
Regional versions
868 / 915 MHz
System
R2/Pico · R2 PRO
Power
2 × CR123A; up to 3 years in standby mode
Operating temperature
−10°C to +60°C
Pet immunity
Up to 35 kg; match mounting and sensitivity to the animal’s route, then test that route.
Radio security
AES-128 encryption, FHSS and TDMA

Nominal coverage under specified installation and test conditions. Match regional detector and Hub variants; follow the placement guide for sunlight and temperature exposure.

Add outdoor motion detection to a compatible Roombanker intrusion alarm system. RBSS-PS2 combines PIR and microwave sensing with an IP54 enclosure. Choose a position away from direct sunlight and sources of significant temperature change.
PRODUCT CAPABILITIES

Outdoor detection, ready for your system

Long-range wireless

Two-way communication with your Hub

Wireless RBF Technology
Dual-technology detection

PIR + microwave sensing

dual tech verification
Battery-powered installation

Replaceable battery power

outdoor pir lithium battery
Temperature Compensation
digital temperature compensation
Adjustable sensitivity
auto sensitivity adjustment
Pet-aware detection

Plan for the routes animals use

PIR detection diagram showing a dog below the detection beams
PIR detection diagram showing a person crossing the detection beams
Setup and testing in RB Link

Add devices. Test signal and coverage.

pir sensor all inclusive app
IP54 outdoor enclosure

Match the enclosure to site exposure

ip54
Tamper monitoring

Tamper event reporting

tamper alarm message
DETECTION PERFORMANCE

Detection & coverage

pir wide angle
pir range

Coverage for the approach you need to protect

Nominal detection coverage is up to 16 m with a 90° angle under the specified installation and test conditions. Match the pattern to the intended crossing paths and verify them on site.

Temperature Compensation

RBSS-PS2 uses temperature compensation to help account for changing operating conditions. Its specified operating range is −10°C to +60°C.

If you install it beside a sunny entrance, follow the sunlight and siting restrictions when choosing the mounting position.

temperature compensation outdoor pir
Outdoor PIR sensor beside a dog, with a 35 kg pet-immunity label

Account for nearby pet activity

Pet-aware detection depends on mounting, sensitivity and the animal’s route. Raised surfaces can change how a pet enters the detection pattern. Test likely animal routes alongside intended crossing paths.

Which indicators help during setup?

The indicator colours and flash patterns show you registration, signal strength and motion detection during setup.

Task or stateIndicator
RegistrationGreen: 250 ms on / 750 ms off
Find MeGreen: 1 s on / 1 s off
Strong / medium / weak signalGreen / orange / red: 3 s on / 3 s off
Lost signalRed: 250 ms on / 250 ms off
Motion detectedRed flashes every 500 ms

To add the detector in RB Link, select the Hub, then “+” and “Add peripheral”. Remove the battery insulation strip. If the device does not appear and the green indicator is off, hold the register button for 5 seconds to retry. Assign a room and complete the addition.

For example, if you see the red indicator turn on for 3 seconds and off for 3 seconds during a signal-strength test, the signal is weak. Signal-strength testing switches off automatically after 2 minutes.

INSTALL & COMMISSION

Outdoor installation

Setup and testing, together

Use RB Link to add RBSS-PS2 and assign it to a room. Follow the RBSS-PS2 quick-start guide for the model-specific steps.
1
Open the app to add pet friendly pir sensor

Open the app to add devices.

2
power on pir

Power on the device.

3
successful pir

Assign a room, then test the site.

Designed for installation and servicing

pir sensor test
Test and Install

Test signal strength at the proposed position before final fixing. Mount RBSS-PS2 at 1.8–2.2 m using the documented wall plate and screws. Run the installation test across the intended paths.

easy maintenance pir
Access for Servicing

Choose a mounting position that remains accessible for inspection and servicing. Follow the current model instructions for battery replacement.

CONNECTED PROTECTION

Wireless system integration

outdoor pir rbf 3100m

Wireless connection. A matched system.

RBSS-PS2 uses the RBF protocol for two-way communication with a compatible Roombanker Hub.Supported systems include R2/Pico and R2 PRO. Match the detector’s 868 or 915 variant to the Hub and project market.The published nominal radio range is up to 3,100 m in open space; test the link at its final installation position.

Connect detection to your alarm system

RBSS-PS2 reports motion events to the compatible Hub. The Hub applies the armed state and configured actions for connected devices. Test each required siren and notification path during commissioning.

Available actions depend on the Hub, connected devices and configuration.

outdoor pir hub camera alarm system
ONGOING RELIABILITY

Maintenance & protection

Over-the-air firmware updates

RBSS-PS2 supports over-the-air firmware updates. Follow the update instructions for the installed device and released firmware.

outdoor pir ota updating

Tamper event reporting

RBSS-PS2 includes tamper protection. Verify tamper event reporting and the configured system response during commissioning.

outdoor pir ota updating
ONGOING RELIABILITY

Maintenance & protection

Model and System Guides

Need more context? Compare indoor and outdoor selection, understand dual-technology detection, or investigate unwanted alarms. For sites with animals, use the pet-friendly PIR guide.

PROJECT QUESTIONS

RBSS-PS2 Project Questions

RBSS-PS2 detects motion using passive infrared and microwave sensing. Both must detect activity for the detector to trigger an alarm. The Hub then carries out the system response you have set.

For example, if you are testing a warehouse entrance, check motion detection at the detector and the configured response at the Hub as separate steps. The dual-technology guide explains how the two sensing methods work together.

Supported systems include R2/Pico and R2 PRO. Match the exact regional detector and Hub variants for the project.

Use the documented wall-plate mounting method at 1.8–2.2 m. Avoid direct sunlight and sources of significant temperature change. See the outdoor detector quick-start guide for the installation procedure.

Include likely animal routes and access to raised surfaces when choosing the position and sensitivity. Test these conditions alongside the intended detection paths.

Test radio signal strength and intended detection paths separately. Then verify the system actions required by the project. The sensitivity guide explains the trade-off when adjusting settings.

Use the RBSS-PS2 specification for model data and the quick-start guide for pairing, indicator patterns and installation tests.

Discuss Your Outdoor Detection Project

Share the site layout, intended crossing paths, nearby movement, mounting conditions, Hub model and market.

Scroll to Top
Contact Us